Guide
Hobart Parts: Genuine vs. Aftermarket and Warranty Rules
How to match a Hobart part number to your exact model, when genuine parts beat aftermarket, and what Hobart's one-year warranty depends on.
The right Hobart parts start with the full model and serial number from the machine’s data plate, because one model family can need different parts depending on the version. If the unit is still inside Hobart’s one (1) year warranty from original installation, contact Hobart Service first; after that, a typical commercial dishwasher repair runs $300–$1,100 and a mixer or slicer repair $200–$950, with the firm quote given on site after diagnosis.
How do you find the right Hobart part number?
The AM16 door-type family shows why “Hobart dishwasher” is not enough. Hot-water models carry a 7.1kW booster that holds a 180°F final rinse from incoming water of at least 110°F. The chemical-sanitizing AM16SCB and AM16VLSCB use a 4.3kW booster sized for incoming water of at least 90°F. Auto-delime versions such as the AM16-ASR pump delime solution in on their own; manual-delime models do not.
Before you order:
- Photograph the data plate: model, serial, voltage.
- Photograph the failed part and any stamped number.
- Note the error code or message.
- Confirm the match with the supplier before it ships.
On LXe undercounters, the LXePR and LXeR pump deliming agent automatically; the LXeC and LXeH do not.
Should you buy genuine Hobart parts or aftermarket?
Hobart Genuine Parts are engineered for the exact machine, which matters most for sanitation and safety parts. Rinse heaters, temperature sensors, control boards and pumps decide whether dishes reach the 150°F wash and 180°F final rinse printed under the AM16 touchscreen on hot-water models. A part that runs a few degrees short means rewashed racks and trouble at your next health inspection. On mixers and slicers, interlocks and blades protect your staff, so buy those genuine.
Aftermarket can make sense for simple wear items, such as some gaskets or hoses, on an older machine well past warranty, if dimensions and materials match.
Is the part actually broken, or is it a maintenance code?
Many Hobart dishwasher messages point to cleaning, water supply or deliming rather than a dead component:
| Code or message | Likely cause | What the owner can check | When to call a technician |
|---|---|---|---|
| AM16 Error 019 | Tank strainer blocked | Clean and replace the strainer pan, press ENTER | It returns with a clean strainer |
| AM16 Error 023 | Fill timeout | Water is on; pressure is 15 - 65 psi | Supply and pressure are fine |
| AM16 Error 080 | Delime reminder | Press ENTER and run a delime cycle | It returns right after deliming |
| AM16 Error 083 / Error 084 | Final rinse below minimum three cycles in a row | Incoming hot water at least 110°F; hold power 5 seconds to clear Error 084 | It persists |
| LXe LOW RINSE TEMP | Rinse temperature missed three cycles in a row | Incoming water temperature | It shows Check Water Input after 10 cycles |
Water quality matters too: Hobart recommends 3 grains per gallon or less for LXe machines and calls for water treatment above that.
What does Hobart’s warranty coverage usually depend on?
Hobart covers new products installed in the United States against defective material and workmanship for one (1) year from original installation, though some products and parts carry other terms. Coverage usually depends on:
- Proof of the install date. Keep the invoice with your data plate photo.
- Following the care instructions. Hobart notes that skipping them may void coverage. For the AM16, clean at the end of each shift or at least daily: hold Power 5 seconds to drain, wash the strainer basket, pan and standpipe, check that the arms spin freely, and never use steel wool.
- Deliming when prompted. With delime lockout enabled, an AM16 locks after the reminder is ignored 10 times.
How do you plan a Hobart part repair around service?
A dish machine down on a Friday night means a three-compartment sink and a slower line. In Paramus, the borough’s blue laws keep Garden State Plaza and most retail closed on Sundays, so for kitchens tied to mall traffic along Route 4 and Route 17, Sunday can be the quietest window for a part install.
Have the model, serial and code ready when you call (914) 350-6776. Paramus Commercial Appliance Repair is an independent service, not manufacturer-authorized; a diagnostic visit typically runs $95–$165. See our Hobart repair page, commercial dishwasher repair and pricing.
Frequently asked questions
Are Hobart Genuine Parts worth the extra cost?
Yes, for anything that controls rinse temperature, sanitizing or operator safety.
Where do I find my Hobart model and serial number?
Both are on the data plate. Photograph the whole plate, because an AM16-BAS and an AM16-ASR take different parts.
Is a repair in the first year covered?
Defects in material and workmanship on new U.S. installations are covered for one (1) year from original installation, subject to that product’s terms; contact Hobart Service first.
Do you repair Hobart mixers and slicers too?
Yes, food-prep equipment repair typically runs $200–$950, with the firm quote given on site after diagnosis.